Porsche’s air-cooled sports cars are legendary, but in the 1970s the manufacturer saw a future in something unconventional for them at the time: water cooling.
The water-cooled, front-engined 924 replaced their entry-level 914 in 1976, but despite good sales, the newer model wasn’t a huge hit with the Porsche …
Shopping and Ownership
Paragon Products has been providing technical assistance to 944 owners for decades. For some maintenance tips, we talked to company owner Jason Burkett.
If you’re looking for a 944 to buy, get the best car you can afford. Fixing up a basketcase can get expensive. One of the big things is to check and see if someone else has paid to do the clutch at some point. A clutch job in these cars is a pain in the butt.
If there isn’t any history of the timing belt/balance shaft belt and rollers being serviced, that would be the absolute first thing to do. This car has an interference head design, so if the timing belt breaks, things get expensive. While you’re in there, plan on doing a water pump unless you know for sure it’s recently been done.
If you have to choose between a Series 1 car (1982-’85.5) and a Series 2 car (1985.5–’92), go with the Series 2 car because of its updated dash and widened track. Also, all of the Turbos are the later style.
Staying on top of the timing/ balance shaft belt situation is very important. Sometimes people ask, ”My car sat five years and the belts look good; should I replace them?” Yes. This stuff isn’t that expensive and you’ll be crying if something does fail, so replace them. This is a good time to check for front engine leaks, as that’s the opportune time to seal up the front of the engine.
When doing a clutch job, do it all: disc, pressure plate, throw-out bearing and what we call a “clutch accessory kit.” Yes, you need it. It doesn’t matter how good the stuff on the car looks. Doing a clutch is probably one of the worst jobs there is on a 944, and you certainly don’t want to have to go back in there because you cheaped out on pressure plate bolts or flywheel bolts.
While owning a 944, you may come across some of the following common problems. One we see often is an odometer that quits working. This is actually repairable. You will need to disassemble the gauge cluster and replace a gear. Step-by-step directions can be found on our website.
If you feel vibration in the steering wheel, it could mean that your motor mounts need to be replaced.
Sometimes, hot air gets blown through the vents in the car, even if you have the air conditioning on full blast. A threaded rod that controls the heater door is attached via a very small and brittle plastic support and metal clip. The support ages and eventually cracks, throwing the clip to the floor and releasing the heat to the cabin. Again, step-bystep directions for fixing this can be found on our website.
Want to put your 944 on track? Make sure that the oil level is always at the top mark before every session. It may seem like common sense, but it’s especially important in a 944. If your car will be heavily tracked, it’s wise to install an oil cooler. Owners of cars with aluminum control arms should check for ball joint looseness before every event. Ball joint rebuild kits are available through Paragon Products.
When looking to add upgrades to your 944, remember, suspension is king. These cars are already pretty well balanced, but the stock stuff is most likely worn out. Just a new set of Konis will make a huge difference. Stage two is to replace the factory anti-roll bars with either the factory 968 M030, Weltmeister or Tarett setups.
Stage three would be to increase the spring rates. This is relative easy on the front with either the Weltmeister lowering springs or our adjustable ride height kit. For the rear, you can either use larger torsion bars or ditch the torsion bars altogether and go straight to coilovers. Re-indexing or removing the torsion bars is a decent amount of work, so a lot of folks don’t want to mess with them. That’s fine, but they should tread lightly on the amount of spring rate they run on the front so they don’t make the car understeer more than it already does with the factory setup. For folks who don’t want to mess with the torsion bars, I usually advise them to go with 200 lbs./in. front springs and then just lower the rear to match.
